All posts made by se200 that members have liked.
Your my hero. I didn't even know this was possible. Thanks you guys rock.
I should have noticed this lol I have read over the help section a ton of times. I corrected this and now I'm good thanks ...
This has been done put the guy used Honda sensors and a Honda distributer. He ran the Honda ecu becauSe at the time we did not have a good low cost map capable ems for our cars. Nismotronic has cha...
MAF replace and all is well. Car runs drive and pulls great on a whopping 4psi. MAC boost solenoid driven by Nemu is working so time to up the boost and tune. I can already tell that this 6spd swap...
Its funny all the guys from up north think this is a good deal and all the guys in the south(FL) think its a rip. Im betting its hard to find these cars not full of rust up north now. Down here the...
I live in Orlando and the small dealers in that area are shady to say the least. That is a clean car but 2600$ is crazy plus the dash has cracks.
Its funny all the guys from up north think this is a good deal and all the guys in the south(FL) think its a rip. Im betting its hard to find these cars not full of rust up north now. Down here the...
MAF replace and all is well. Car runs drive and pulls great on a whopping 4psi. MAC boost solenoid driven by Nemu is working so time to up the boost and tune. I can already tell that this 6spd swap...
So looking over the base/start up tune I got from jktuning it is almost identical to the one I made. So I uploaded it and have the same issue still. Now this turns out to be a good thing because if...
looks like a good day. We are planning to meet up on the 26th for a track night if any of you guys can make it.
Msd 96lbs $80 shipped.... I had them and a set of 72lbs just siting around.
Id1000s 380$ plus shipping
I'll get it sorted and then share so other ppl Have more options.
looks like a good day. We are planning to meet up on the 26th for a track night if any of you guys can make it.
[url= URL=http://smg.photobucket.com/user/nooch8it/media/Mobile%20Uploads/2244C8FF-4D32-41B9-BADC-AB208B775EB8_zpsozr2letu.jpg.html][img]http://img.photobucket.com/albums/v354/nooch8it/Mobile%20Upl...
Why the F#^*%#%# did you post a pic of someone else's setup asking for help on how to fix it. I'm sorry for being a dick face but we can't help you if we can't see what you need.
Why the F#^*%#%# did you post a pic of someone else's setup asking for help on how to fix it. I'm sorry for being a dick face but we can't help you if we can't see what you need.
As stated above, your missing a bolt on the oil outlet. Drill the holes out on the flange and use two bolts. You also need two hose clamps one on each end of the rubber hose. If the fitting is leak...
^^^ well good news... My setup is a bit different due to the 6spd. So it sounds like this clutch works fine with the cable. I do get chatter but only a little bit when taking off slow in traffic. B...
Rb25det use the same injectors as the sr20det, sounds like another confused 240sx owner. I have owned both an sr20 swapped 240sx and rb25 swapped 240sx. Rb25/20 is a junk box the sr20 will support ...
The eBay add says sti inj and those should be high imp. As for the Rb inj you would need to provide more info. Just check them with a meter.
Stick with sti 555cc inj if that's what your tuning f...
Yes that was an Orlando car I have done work to it for the last owner. He took really good care of the car and loved it I know he was sad to see it go.
If the 97 se-r came 5spd then it should have an LSD trans in it so make sure your not about to do work for nothing. As for swapping parts don't bother pulling gear stacks. Open up both cases and ju...
[url= URL=http://smg.photobucket.com/user/nooch8it/media/Mobile%20Uploads/4825223D-0B14-4791-938C-FCF254DF4ABE_zps4dr1nhva.jpg.html][img]http://img.photobucket.com/albums/v354/nooch8it/Mobile%20Upl...
[url= URL=http://smg.photobucket.com/user/nooch8it/media/Mobile%20Uploads/4825223D-0B14-4791-938C-FCF254DF4ABE_zps4dr1nhva.jpg.html][img]http://img.photobucket.com/albums/v354/nooch8it/Mobile%20Upl...
I use the cig lighter 12v and a chassis ground with no issues.
Enthalpy has been around for a while, years. They are 240sx tuners and don't really play with fwd. you can get a Nemu stand alone for your fwd sr for the same price as a basic chipped enthalpy unit...