JKTUNING's Likes Given

I love my wife more than you guys will ever imagine... At the end of the day she is my biggest supporter.

Thanks kevwal.. That was on a 23" tire. The car runs straight as an arrow.

Old Man:
http://25.media.tumblr.com/tumblr_mc3hg5VpQP1qcy0p7o1_500.gif

Me:
http://media.tumblr.com/tumblr_ljls50q7No1qcryjz.gif

The Official 2014 SR20 National Convention Information Thread!

This makes me want to take my sfac and current ecu and throw it in the trash lol.

Thanks again for the generosity. I remember all the excitement in the room when we called the winner for this pr...

Well I went over the entire system and found no leaks. I took the boost controller apart and it's fine, but then I figured I'd see how well the sintered brass filter on the bleeder port flowed........

The class was really good, it honestly changed the way I thought about tuning. The biggest takeaway for me was that the way to tune correctly is to make your fuel table reflect what you want in rea...

I can really say that for me, i went from not knowing a whole lot of Nismotronic, I learned a lot and now have a pretty good idea of where to go.
While i was there, I got SA package (thanks John!) ...

MAF replace and all is well. Car runs drive and pulls great on a whopping 4psi. MAC boost solenoid driven by Nemu is working so time to up the boost and tune. I can already tell that this 6spd swap...

I was told the pricing went up on these clutches.. try ebay.. otherwise contact Doug Fab or TRACKFORGED as they are both dealers.. however I haven't seen one cheaper then on ebay but I dont mind pa...

Got the rest of my goodies from Doug Fab whoohoo!

http://i1317.photobucket.com/albums/t631/lynchfourtwenty/joshs/20140408_174131_zpsadoj8d9t.jpg

And ofcourse some swag!

http://i1317.photob...

It doesnt matter, just hook one to 12v switched an the other to the ecu.

EBC setup -- (ecu based boost control)

yea i just went down and snipped them. and the logger is reading properly now. all my information is correct. reading dtc codes now. i have a ect lol. said i was at 111 degrees when i hadn't starte...

Its ALIVEEEEEEEEEE!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! cutting the the consult wires worked. Wires 7,14,15.

This trip will probably cost me more than I paid for NEMU by the time I pay for the class, hotel and, rental car but I want to learn as much as I can about this so I can get the most out of the NEM...

Sounds awesome... get all those last minute, pre-convention bugs worked out and actually know how to make meaningful adjustments at the track!

Sent from my SAMSUNG-SGH-I317 using Tapatalk

I'm normally a old school Greddy profec b spec1 type of guy, but I'm gonna let my Nemu do it for this time around

nvm, i see u already responded. thanks!

Ben - turn your head to the side... lol

Re: NismoTronicSA Tuning Class

Yes! I would love to understand all the fine detailed stuff, like the accel/decel fueling and other random bits and goodies. General tuning tips can't hurt either..



edit: annnnnd I'm registered

Thanks for the offer, I like to try to solve things myself, but I will resort to sending it to you if it's an emergency :) NEMU is so user friendly :)

Thanks, I will try that. Just remembered that I got "Code 11 - Crank Angle Sensor " two weeks ago, but I haven't gotten that code since. It's probably my distributor or wiring that is at fault here...

I don't think a SR20DET ECU is good enough. It needs to be one that was used on an engine with COP to begin with. This means most FWD ECUs are not going to work. You probably want one from a RWD ca...