All posts liked by Mattick22
New Garrett GTX2971R and GTX2871R models
Andrew, I ordered two sets of NISMO valve stem caps so I could see which looked better on my car. I know it's hard to believe I went with the all black ones.
I'm sending you the extra set.
...
Andrew being the incredibly good guy he is, objected strongly and sincerely to my offer. Didn't know if he could possibly accept. Too generous. Not necessary. Yada, yada.
Me, being the assho...
If everything seems normal, no need to tear it down.
Heck, SR20's are tougher than most think, I've hydrolocked mine with fuel (don't ask me how), and overheated the coil by cranking it with no pl...
I love my meziere pump with Davies Craig pump controller. It is a great setup, the pump will run on with the car off to cycle coolant and cool the turbo down and so on. Very cool controller. I l...
[url= URL=http://s494.photobucket.com/user/b15ser20/media/1902806_850431194997359_8955645407454863080_n_zpsc5df1779.jpg.html][img]http://i494.photobucket.com/albums/rr308/b15ser20/1902806_850431194...
This with all the rear ends on the back would be super cool. I won't be there but will buy one to support the cause! Dave
You don't need to bend any pipes.The kit comes with i/c pipes with angles/bends/lengths of different variations.Just a matter of piecing the intercooler pipes together after measuring and cutting w...
B13
SR20VE+T
EMS Stinger 4424
Eagle Rods
Weisco Pistons 8.5:1
Protech Tubular Manifold
Precision SC61 (Stage 5 rear wheel, E-Cover Comp.)
Tial 44mm
N1 Ported Manifold by Miko
Nismo 740cc I...
http://i494.photobucket.com/albums/rr308/b15ser20/dafc48ff67f75d2a634272536b25b166_zpsded12893.jpg
Re: Post Your B14 Pictures (Not So Silent)
Well I went over the entire system and found no leaks. I took the boost controller apart and it's fine, but then I figured I'd see how well the sintered brass filter on the bleeder port flowed........
Lets get these pictures up, you guys are just barking in the dark. OP, throw up them pictures of the item, the damage, the box/packaging, the conversation.......jordan, any pictures of the item pri...
Searching and how hard it is here
I knew I should have went with my usual rule of not replying to audio on a car forum.:cool::rofl:
You will NEVER EVER EVER EVER......reproduce the sound of even shitty 2 dollar headphones in a c...
Post #101 may have your awnser. It's not 100% clear on the rears though. Dave
http://www.sr20-forum.com/information-library/30432-brake-thread-3.html
The brakes of 100NX GTi(NX2000),Sunny/Pulsar GTi/GTi-R (N14 which is B13) and Almera GTi( N15/B14) in Europe are all the same fronts and rears:
256x26mm vented fronts + AD22VF
258x9 solid rears (...
http://img.photobucket.com/albums/v87/Storm88000/82pics_zps71943cb6.jpg
http://i1239.photobucket.com/albums/ff512/spazmar/20140616_171324.jpg
Genuine Autech HB14. First B14 I've ever owned.
This is good advice ,too. You wont hear the rears much with an amp on the front speakers.You can actually run all 4 off the 2 channel amp if its stable to 2 ohm stereo......but I didnt go there as ...
Here's my EHPS mounting location. Since it's on a P10 chassis, the coolant overflow reservoir has to be relocated.
[url= URL=http://s481.photobucket.com/user/Socalvvl/media/IMAG0230_zps177de125...
A semi tucked new harness would be awsome. Wiring specialties was looking to see what kind of demand there was at some point and there was interest just not enough for them i guess. There was also ...
Travis's 200sx Se-R with pulsar front end (video)
The injectors can run without the resistors but you can damage the injector drivers in the ecu. No matter what ecu you use it needs resistors, that's why the GTI-R came with a resistor pack. Most l...
Im gonna bet theres no resistors wired in or the gtir ecu is burnt out