Chriscar's Likes Given

Should we instead focus on resolving the tune problem?

Both the fuel decel and general richness can be attributed to a faulty engine coolant temp sensor. Was the correct sensor used with the Nis...

Disagree entirely. Shawn's reference to OEM or OEM+ is in terms of functionality and operation. Something that is easy achievable with the litany of parts and tuning solutions made available to use...

I'm hoping it involves the words of "i screwed up" or "that is my fault". Unless there is something egregious that we've all overlooked or don't know about, I'm unsure how any other response makes...

I think it is safe to say that you will NEVER find a car as reliable, fun to drive, forgiving or as personable as a B13 SE-R. I know this as I've owed three B13 SE-R's (one that I owned twice) as w...

I know from personal experience that brakes are better than feet... I remember it like it was yesterday... (Cue the harp music)

I was leaving for work and when I started the car, the engine wa...

Parade laps can definitely be a lot of fun. I was at a race a while back, and heard them announce that the parade laps were going to happen after the testing day shut down at 5pm. I immediately s...

Since we're on the topic... I think parade laps at lunch would be a great thing for the convention track day. A lot of groups are doing it these days. You have a session during lunch where you can ...

Well you can stay home then and massage your vaj! :D

NismoTronicSA - NEMU2 Updates

using common sense would have avoided all of it earlier as well... using a ruler when building these and this wouldn't have been an issue to begin with.

I could be out in left field on this, but this is what I've gathered throughout the years.


Top-feed pros:
Better availability, especially as flow-rates increase
Cost (cheaper)

Side-feed pros:
Ou...

Pulled the invoice from my local dealer. I purchased the knob in September of 2014.

I bought a Z32 shift knob at the same time and the Z32 shift knob sits "lower" when compared to the B13 shift ...

Yes. It will. :)

To clarify to others, the build needed a bit more shake-down time. Mark (and entire crew) was insistent on making it 100% right, they flew me home and Mark personally drove the...

Hank was at the picnic (no award for heaviest car ;) ). And there are reasons why I did not post Shawn B's car. Those that were there at the Convention already know why the car did not return home ...

OP, a 205/50/15 will be as close as it gets. Here are some numbers

225/45/15: 583.5mm (total tire diameter)
205/50/15: 586mm (total tire diameter)

http://www.willtheyfit.com/index.php?width=225&a...

[img][URL=http://s579.photobucket.com/user/ssgrob/media/11046376_10206254652828359_3027535617502746662_n.jpg.html][IMG]http://i579.photobucket.com/albums/ss231/ssgrob/11046376_10206254652828359_302...

Took the car to get dynotuned,then swapped my ssac for one of the ebay tri-y for testing...and retuned.
Added N1 cams and retuned again.
Stay tuned for a full writeup and dyno sheets as soon as I...

Keo, I dont know you personally but you are a respected member here on this board and I think we can both agree that's a little far stretched from the truth. There are definitely members on this bo...

Just reinstalled my original 94.5 B13 LE radio back into the car. Has a date of manufacture sticker on it for 4/29/94, and my Sentra was built in May 94. The radio has been in a plastic bag since ...

After about five years of sitting in the garage under a cover virtually untouched I began to work on her. Did a few minor things last night. My goal is to bring the car back to stock as much as pos...

I've been on my death bed this past week, so I've been a ghost online. Sorry about that.
LAM-PARK has been doing a great job of keeping track of the trail of tears B14er has left behind so...

In case you hit the rev limiter without them, you may spit a shim out into the oil pan or the rocker gets kicked off.

If you hit the rev limiter with the rocker arm stoppers, it can stick a val...

needed to make another tool.......

http://ost.ebeans.ch/albums/userpics/10005/homemade_measuring_caliper_2_panel.jpg


A stock intake port is approximately 27mm (+ or - .25mm) and 100mm long @ tha...

4 B13's, 3 SE-R's and counting...

I'm no expert on dampers, but I think that the idea is to use the smallest amount of damping that will control your springs and prevent multiple oscillations. If you use more damping than necessar...