lynchfourtwenty's Likes Received

I think the only reason the guy hasn't been banned is because of who he knows, had this been joe schmo they woulda been gone along time ago.. if you cant ban him from the forum ban him from the cl...

I think the only reason the guy hasn't been banned is because of who he knows, had this been joe schmo they woulda been gone along time ago.. if you cant ban him from the forum ban him from the cl...

i figured.. lol

now finish breakin in that clutch!

im just going off what i read on motoiq man honestly, theres a little bit that can be ported but idk..

we put a vet pump on nate's de an that shit will peg the 150psi gauge around 5500-6000rpm l...

yep might of fried da maf :( that sucks.. if a + an a - touched and its not workin right any more after wiring it correctly i'd guess that either the maf fried or something on the ecu, lets hope i...

uhh not sure on the size, my rail has barbed fittings since im not upgrading to ss lines.. but yep them are id1000's! :)



on another note i swapped transmissions today and man is that a chore by ...

Got the rest of my goodies from Doug Fab whoohoo!

http://i1317.photobucket.com/albums/t631/lynchfourtwenty/joshs/20140408_174131_zpsadoj8d9t.jpg

And ofcourse some swag!

http://i1317.photob...

I was told the pricing went up on these clutches.. try ebay.. otherwise contact Doug Fab or TRACKFORGED as they are both dealers.. however I haven't seen one cheaper then on ebay but I dont mind pa...

Got the rest of my goodies from Doug Fab whoohoo!

http://i1317.photobucket.com/albums/t631/lynchfourtwenty/joshs/20140408_174131_zpsadoj8d9t.jpg

And ofcourse some swag!

http://i1317.photob...

well so far this is working great on boost by gear all set to 8psi which is actually just about spring pressure, the cars pretty much ready for the dyno where we can dial it in :)


JKTUNING you...

that should be added to the manifesto Shawn B

i dont know how to make it any simpler dude..

http://i1317.photobucket.com/albums/t631/lynchfourtwenty/letmedrawyouapicture_zpsbff92f7a.jpg

hell ya! thanks for all the pics :)

little bit more info: Turbo is a Precision GT2871R and its got the .86 exhaust housing, this should be quite the setup.

im fuckin excited!! lol

Check for spark man?

Take a spark plug wire out of one of the holes an put a spare spark plug in it an ground the tip while someone trys starting the car.. you should see it sparking.. if not th...

Got the rest of my goodies from Doug Fab whoohoo!

http://i1317.photobucket.com/albums/t631/lynchfourtwenty/joshs/20140408_174131_zpsadoj8d9t.jpg

And ofcourse some swag!

http://i1317.photob...

I had a buddy helpin me once an when he put the starter cable on it was at a funny angle so it was making both posts on the solenoid contact.. as soon as I turned the key I blew the ignition relay ...

EBC setup -- (ecu based boost control)

It doesnt matter, just hook one to 12v switched an the other to the ecu.

EBC setup -- (ecu based boost control)

EBC setup -- (ecu based boost control)

The jgy pp is most likely at fault for the disc.. my jwt pp an b15 disc had put up with much worse lol.. either that or your missing dowel pins..


An ya the fx clutches have a great pedal feel....

Or the issue could be with your injector battery offset, as you put more load on the alt the voltage can drop an u will use a different cell in your injector battery offset table..

This has cure...

ben, 2.3 can be just pistons too if ya bore to 92mm

dougs like tittys.. i like em :)

dougs like tittys.. i like em :)