All posts made by jimbo_se-r that members have liked.
The new forum software will be the most challenging piece, writing from scratch will be quite an undertaking. I'd much rather completely rebuild my car... :bigthumbup:
The new forum software will be the most challenging piece, writing from scratch will be quite an undertaking. I'd much rather completely rebuild my car... :bigthumbup:
The new forum software will be the most challenging piece, writing from scratch will be quite an undertaking. I'd much rather completely rebuild my car... :bigthumbup:
OK, I had the right sizes above, 10mm square drive for the fill plug, 13mm square drive for the drain plug. Both are male square sockets.
I was able to find the 13mm one at the local NAPA Auto ...
I have this info at home, but I believe the drain was a 13mm, and the fill was a 10mm. I bought them both for around $5 each. Will confirm and update tonight with this info.
Maybe they're saving that for the 30'th Anniversary Edition. They already missed out on the 25th anniversary...
The good news is, with more models using this motor, in 10 years or so, parts will be plentiful at the local junk yards.
The good news is, with more models using this motor, in 10 years or so, parts will be plentiful at the local junk yards.
The good news is, with more models using this motor, in 10 years or so, parts will be plentiful at the local junk yards.
Yes, I agree with that. But my point above on total height was, imagine you didn't have a spring on the strut. It really couldn't be any taller than it is now, right? With the insert placed in t...
Fast and efficient. As far as the base, yes, could be more stable, but honestly no different than any other home method I've seen people talk about.
When you say they are hard to read during the day, I'm assuming you've seen them in person? Are both red and blue hard to read? I've seen pics of them installed and they looked nice, but I've nev...
You were almost there on posting your pic. From that web hosting page, click the Arrow below your pic to Share the photo, click the BBCode tab, go to Original Size, and copy the code there. All y...
Depending on the switch, the ECU will either think you're always in neutral (which would explain no cruise), or never in neutral. Sounds like the always neutral is what is being sensed right now.
Get underneath the car, bring that cable straight up the back of the transmission, and see if you can get the connector to rest or hook on to something. Get up top, pull the cable a bit (not too h...
I totally respect the person giving this advice, but I'm hesitant to recommend adding parts when there may still be some mechanical or electrical issue causing the problem. You always need to tack...
I totally respect the person giving this advice, but I'm hesitant to recommend adding parts when there may still be some mechanical or electrical issue causing the problem. You always need to tack...
What Did I Do To My B13 Today? I went out and got a new sticker for it...
Out with the old...
http://www.4shared.com/img/g9B2mQP4ba/s25/15679f324a8/img_1361
In with the new...
http://www...
What Did I Do To My B13 Today? I went out and got a new sticker for it...
Out with the old...
http://www.4shared.com/img/g9B2mQP4ba/s25/15679f324a8/img_1361
In with the new...
http://www...
What Did I Do To My B13 Today? I went out and got a new sticker for it...
Out with the old...
http://www.4shared.com/img/g9B2mQP4ba/s25/15679f324a8/img_1361
In with the new...
http://www...
What Did I Do To My B13 Today? I went out and got a new sticker for it...
Out with the old...
http://www.4shared.com/img/g9B2mQP4ba/s25/15679f324a8/img_1361
In with the new...
http://www...
Thread courtesy Kyle:
http://www.sr20-forum.com/information-library/73322-oem-exhaust-manifold-hardware-studs-nuts-washers-photos.html#post1047361
Just an FYI for future google searches... I found in the FSM in I believe the EF & EC section some information on the ECU's failsafe modes, one of which covered if the temp sensor wasn't reading c...
Stupid, stupid, stupid... I checked my relay wiring twice, but I checked it wrong... The problem is my new relay wiring. I disconnected the cable going to the ECU and jumpers the blue wire to gr...
As I understand it, from an exhaust flow perspective, you want the diameter to get larger the further away from the engine you get. This maintains the velocity of the gasses, and creates lower pre...