zeneffect's Likes Received

drove it to work, smashed the living eff out of a s14 yesterday while i was out and about. watched the guys face go from a sarcastic laugh to pure disappointment as he kept getting smaller in the ...

Not so much did to but did for

Went junking today

http://s28.postimg.org/vjp8cnr19/image.jpg

Went back today to grab these, they are a little dirty as I didn't clean them up but otherwise in perfect condition. I was quite surprised when I got home and looked at the transmission bracket ye...

yes, it got quieter actually.

the ssac header isn't that bad. its not that bad at all.

Dat ass

not trying to step on any toes, but I don't really appreciate being shitted on either for my efforts. thanks guys for the kind words, squirlz, no hard feelings... its been one of those days for me...

if you read through this thread, searched, and compared previous data there is. If choose to post what mods are done or not is my choice, if you dont like it well too bad, its not your car i have ...

if you read through this thread, searched, and compared previous data there is. If choose to post what mods are done or not is my choice, if you dont like it well too bad, its not your car i have ...

if you read through this thread, searched, and compared previous data there is. If choose to post what mods are done or not is my choice, if you dont like it well too bad, its not your car i have ...

dat ass

so i read through a shit ton of posts about the stepping sizes and dimensions. this header is VERY similar to the honda big tube stepped tri-y header. the 4-2 is slightly larger and the 2-1 is as...

we cut the nipple off the hp hose to rotate it more. seems easier than modding the bracket imo. that hose is on there pretty tight so i doubt it will rotate on its own, just be careful when torqu...

4pk775 was a winner! So ve + gspec crank pulley = 775mm length fits and gets the alternator way out of the way

there is a trick to getting it on and it requires 2 people. 1 can be whoever, even ...

front to back based on a measuring tape and some math

1st step 1.67 OD
2nd step 1.78 OD
3rd step 1.9 OD
1st Y 2.037 OD
2nd Y 2.54 OD

http://s7.postimg.org/guhva431n/image.jpg
http://s7.postimg.or...

^this

with instructions that are printable no less!

VQ35 Swap Install Instructions - FI-R Write up

did you check for change in the trunk?

not much done to the car to be honest. gspec crank pulley, n1 cams, n62 maf, nismotronic, 2.25 ss vrs exhaust (will change very soon,) 3" intake @ 18in length, bpi velocity stack, fx500 clutch. ...

Dude it's just a belt not a big deal. I didn't dent anything and the alternator doesn't need to be modded. The information to get it on as easily as possible is now available. If you can't perfo...

Dude it's just a belt not a big deal. I didn't dent anything and the alternator doesn't need to be modded. The information to get it on as easily as possible is now available. If you can't perfo...

4pk775 was a winner! So ve + gspec crank pulley = 775mm length fits and gets the alternator way out of the way

there is a trick to getting it on and it requires 2 people. 1 can be whoever, even ...

maybe the belt im running right now will work out best for you. once i get a good belt on hit me up and i can send it your way to test. there is only 1 thing that i request if i do this. post up...

http://s30.postimg.org/h89g6akld/image.jpg

4pk775 was a winner! So ve + gspec crank pulley = 775mm length fits and gets the alternator way out of the way

there is a trick to getting it on and it requires 2 people. 1 can be whoever, even ...

http://s30.postimg.org/h89g6akld/image.jpg