All posts made by Storm88000 that members have liked.
Dodge Shadow turbos? Seriously? How many were made, like 34?
I've never seen one in person in my entire life. I'm sure they are cool though.
The SR20VE motor is the future of the SR20 community.
When the SR20 community started, a Sentra that ran stock 15.8 in the 1/4 mile was insane. Now, new freaking minivans run better than that.
...
The SR20VE motor is the future of the SR20 community.
When the SR20 community started, a Sentra that ran stock 15.8 in the 1/4 mile was insane. Now, new freaking minivans run better than that.
...
Yep def looking into those Direzzas!
Cleaned it:
http://img.photobucket.com/albums/v87/Storm88000/b670e4e7-253e-4406-9c80-2abbd190aea0_zpsf4d15cb6.jpg
****MAY 2nd, 2013 update****
SR20VE head gasket swap is complete:
- I went with the thicker one from Greg normally used for VE turbo applications, but less likely to fail over time. This may hav...
****MAY 2nd, 2013 update****
SR20VE head gasket swap is complete:
- I went with the thicker one from Greg normally used for VE turbo applications, but less likely to fail over time. This may hav...
I pretty much despise anything with the word "bearing" in it
I pretty much despise anything with the word "bearing" in it
Ok so I used Nail polish remover and WD40. It did not work well, BUT the nail polish remover worked ever so *slightly* - it took a tiny bit off. But not noticeable much.
So since acetone is in n...
Had to replace one of my headlights on my '97 SE-R and thus both of them. Went to a junkyard and found a set of the OEM 1999 Sentra headlights. Already had clear corners, got a 98/99 grille from ...
Oh and also, if you have a 91-92 with no airbag, its pretty easy to remove the steering wheel. Pull off the center piece then use your stock tire iron to loosen the nut holding the wheel, then gen...
I'd say a stock Acura Integra GS-R would lose to a NX2000 with the SR20VE swap because the VE has a lot more torque down low. Hell, a stock or lightly modded SR20DE will give a stock GS-R a good run.
Ben replied again:
Hi Jordan
The goal is to make a cam profile that will make more power than the N1 cam for the SR20VE in a normally aspirated application. We will likely entertain making a tu...
They charged you $300 for labor even though you brought the whole transmission to them out of the car?
I was in timing mode when I set it. You know the whole disconnect the TPS, rev engine past 3k a buncha times etc.
Then went to use the timing light and.. nothing.
Word of warning too.. thi...
http://img.photobucket.com/albums/v87/Storm88000/image-1_zps29f7ce6c.jpg
.
.
http://img.photobucket.com/albums/v87/Storm88000/image-1_zpse44a4627.jpg
http://img.photobucket.com/albums/v87/Storm88000/image-1_zps29f7ce6c.jpg
.
.
http://img.photobucket.com/albums/v87/Storm88000/image-1_zpse44a4627.jpg
http://img.photobucket.com/albums/v87/Storm88000/image-1_zps29f7ce6c.jpg
.
.
http://img.photobucket.com/albums/v87/Storm88000/image-1_zpse44a4627.jpg
The differences between the 1.6 and 2.0 in the B14 chassis are:
1) Engine (of course)
2) Transmission
3) Suspension
4) Limited slip differential (except in 98-99 models which didn't have it e...
Ahhhh ok. the timing light worked then stopped working. I guess it sat in my car too long, weird. I think its busted. Oh well. Whats another $18 when I already spent thousands