Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: Twinscroll + Dual Plenum intake manifold + vertical flow sr20det ***photos***

+ Reply To Thread
Posts: 1-10 of 28
2017-05-02 16:13:04
#1
Twinscroll + Dual Plenum intake manifold + vertical flow sr20det ***photos***
hey guys whats up. I recently got my b14 with sr20det up and running with a nice dyno tune. Everything was imagined, designed, built from start to finish by me. As a motorsports fabricator by trade a little custom work was right up my alley.

Setup right now

Bone stock sr20det with lsd b14 trans
Custom Evolved twinscroll turbo manifold with evo 9 turbo
Custom short route piping with 900capable vertical flow intercooler
Custom Evolved dual plenum intake manifold with tapered fully rolled runners
NismoTronic
MBC for now until I wire in the 3 port
Mehh 750cc sidefeed 5-O injectors
Custom O2 housing with 45mm turbosmart external gate and 2.5" downpipe
Custom 2.5" v banded midpipe with 2017 dodge viper muffler and turndown






On low boost 93 octane conservative tune Jorge @ HCar was able to put down 318whp 266wtq. The low tq was due to me not using a strong enough wg spring to overcome exhaust backpressure at all times with the manual boost controller.

The plan is to upgrade to ID1000s and headgasket/studs/cams with E85 and push 400/400. There is a half mile event in November and I would really love to aero the chassis out and see what it could do. Looks like I'm going to have to save up for a b15 trans to hold the power too.




























Last edited by VinceFab on 2017-05-04 at 15-35-01. Reason: added photos
2017-05-02 16:26:02
#2
IG is vince.fab


Apparently I have to make 10 or 12 posts to get content to show lol. Bear with me guys, I promise its worth it!
Last edited by VinceFab on 2017-05-02 at 17-08-28.
2017-05-03 09:57:56
#3
@BenFenner @Kyle

Can't wait to see the pics.
2017-05-03 18:41:26
#4
Just saw your IG! Nice work !
2017-05-03 19:09:59
#5
Originally Posted by Alex_se_r
Just saw your IG! Nice work !


Thank you! Hopefully I can provide some fresh parts for you turbo guys. My brother, TurboFX, doesn't have much time to make stuff anymore.
2017-05-03 19:48:09
#6
Javier from turbofx? Many guys have been looking for him.
2017-05-03 20:35:52
#7
Originally Posted by SR20NYC
Javier from turbofx? Many guys have been looking for him.



Yup. It's even hard for me to get a hold of him most of the time. They looking for suspension parts?
2017-05-03 20:42:10
#8
yes, those rear lca.
2017-05-03 22:46:54
#9
Originally Posted by 1fastser
@BenFenner @Kyle

Can't wait to see the pics.
Also looking forwards to pics.
If there is something preventing Vince from embedding them, it's likely no longer an issue. I checked the normal things and all looks good. If still not able, give it 6 more hours and that should do it.
2017-05-03 23:00:58
#10
Originally Posted by BenFenner
Originally Posted by 1fastser
@BenFenner @Kyle

Can't wait to see the pics.
Also looking forwards to pics.
If there is something preventing Vince from embedding them, it's likely no longer an issue. I checked the normal things and all looks good. If still not able, give it 6 more hours and that should do it.


Pix are up! just dug through the source for jpgs. it worked fine

Interested to hear some feedback...kind of a different build
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top