All posts made by TheSam that members have liked.
Re: Vehicular ECU Wiring Harness Pinouts
Said car lapping the Nurburgring
https://youtu.be/UvmfFBBD94k
Said car lapping the Nurburgring
https://youtu.be/UvmfFBBD94k
Re: Timing chain tensioner going bad? (I have the old style one wth?)
Whenever you make any large changes to the ride height at the rear, you should loosen all of the beam mounts, linkage bolts etc and bounce the car a few times and re-torque everything.
That allow...
shouldnt require any work. If the stock ring bolt doesnt fit the mfactory diff they should be rectifying that.
Quaife into a 32a
http://i63.photobucket.com/albums/h131/shagalata/Quaife%20ATB/IMG_...
Bolts are the same between the 32a and 70a
I've swapped several Quaifes from 32 boxes into 70's now.
My experience with the laminova comes from a boosted Suzuki swift setup, he was having issues on track with oil/coolant temps, once a he installed a laminova setup the temps were solid. They reall...
ATI Super Damper (racing crank pulley) for Nissan SR20 FWD Engines
Failure on Competition flywheel
Cut N Pasta
" Viscous Diffs
The viscous differential also has interleaved plates, and in fact works because of the viscosity (internal friction) of the silicone fluid that fills the gaps between t...
get on with it you nancy
It takes a hell of a lot of revolutions to get the marks on the chain to line up again. If you had everything set as per the FSM you will have nothing to worry about.
It takes a hell of a lot of revolutions to get the marks on the chain to line up again. If you had everything set as per the FSM you will have nothing to worry about.
https://fbcdn-sphotos-a-a.akamaihd.net/hphotos-ak-xaf1/v/t1.0-9/10968586_10155195360155711_944185038084337917_n.jpg?oh=7243a0ba0aed8ce6c6ffe5349ca62ac7&oe=556C62D4&__gda__=1432397667_14a8318acb1f01...
It means the copper washers on the pressure hose, you don't need to touch them though, just remove the 14mm pivot bolt and move the pump out if the way, no need to disconnect any hoses.
Will give ...
He has a daughterboard ECU already a 'powerland' from the guy in Greece.
Best bet is just get a 2 litre crank and rods, use your n1 pistons with new rings.
Get a new oil pump, check the cams unde...
The machine shop has a torque plate, I'm also giving them a gearbox bell housing to bolt to the block whilst its done.
You won't be able to use the 70a pinion shaft in a 70v box.
The pinions and ring gears are matched pairs, the ring gears cannot be interchanged either, V boxes have more bolt holes.
You won't be able to use the 70a pinion shaft in a 70v box.
The pinions and ring gears are matched pairs, the ring gears cannot be interchanged either, V boxes have more bolt holes.
The machine shop I would be using have an SR torque plate, they maintain a few privateers btcc sr20s so that's not a problem.
http://img.tapatalk.com/d/14/09/30/rytemage.jpg
70V
http://www.nicoclub.com/FSM/Sentra/2001_Sentra/mt.pdf
70A
http://www.nicoclub.com/FSM/Sentra/2004_Sentra/mt.pdf
Contains unread posts
Contains no unread posts
Thread is closed
You have posted in this thread
Back to top
