All posts made by Vadim that members have liked.
Don't forget USDM Roller Rockers are different then the rest of the world. UK eventually switched to USDM styled RR with same intake manifold. Before that JDM Roller rockers had the same manifold...
What base ECU are you running?
Usually NA engines will make best power between 12.5-13. Without a dyno it's hard know for sure, thus try to shoot for 12.8 AFR.
As for timing, this will vary,...
There some WRX piping kits for FMIC's, the extra length could help with some turbo lag (to avoid always being in boost at 70-75mph). Thing is FMIC piping plus eBay FMIC cost less then an STI TMIC ...
Knocked the timing down from 38* to 30* at 2800rpm range. Drove 70mph max for 205 miles, with about 10 city miles. Filled up 5.95 gallons = 34.39mpg. Finally getting somewhere. Roller rockers r...
Knocked the timing down from 38* to 30* at 2800rpm range. Drove 70mph max for 205 miles, with about 10 city miles. Filled up 5.95 gallons = 34.39mpg. Finally getting somewhere. Roller rockers r...
My mistake, I used the wrong word, Jacking forces are actually different then what I thought they were. What I meant by that is, with a bigger front roll couple there is a bigger lever to roll the...
Why not just repin your 32 bit harness to OBD2/1? [url= URL=http://www.sr20-forum.com/members-rides/60073-2001-sentra-se-w-pp-sr20det-7.html#post927554]Easy peasy[/url]
Proper name for that guy...
This could be the case I did notice the beam flex quite a bit with not much force. This is why I'm against jacking the car up by the beam, the body weight could actually bend the beam to have less...
BenFenner is the new Shawn B while Shawn is away. :bigthumbup:
Mechanically bent it, I don't have a torch hot enough for heating (MAP w/oxygen doesn't cut it still).
Hank wasn't bashing the beam in that post, he was talking about the SRL only, two diffe...
Don't get me wrong, I don't like the SRL setup at all. But with the right spring rates and swaybars, it's not all that bad. Mike K and Joe from 2JR, all have won races and even set records on an ...
Yeah they probably did it right then. How low is your rear right now?
That's probably it, thrust angle gets real bad if you lower the car more then 1".
As for the bushing binding, I actu...
Trying out the Mustang Mach 1 lip
http://images.rvsmods.com/var/albums/Cars/G20tKH3/Mods/Cosmetic/Lip/Mach1%20Lip_003.JPG?m=1367540099
Pigging through some turns
http://images.rvsmods.com/var/...
It's not a real swaybar for say, Addco bar is technically a reinforcement bar for the rear beam. The rear beam works like a rear swaybar, but it's fairly flexible, so the Addco bar does make a ver...
I paid $60 shipped for mine from [url= URL=http://www.americanmuscle.com/9904-chin-spoilers.html]AmericanMuscle.com[/url]
I stopped being lazy and updated the first thread with the two new flywheels.
First post was pending approval that's why it didn't show up, all good now.
Injector Latency will affect the idle the most, but will also affect the whole fuel map.
Best way is to increase the 4 cells around idle area.
BenFenner is the new Shawn B while Shawn is away. :bigthumbup:
BenFenner is the new Shawn B while Shawn is away. :bigthumbup:
BenFenner is the new Shawn B while Shawn is away. :bigthumbup:
When he bought the item, did you first ship the item then expect a payment? No, you asked for a payment then you shipped the item. Now you are essentially buying back the item, so why should he s...
When he bought the item, did you first ship the item then expect a payment? No, you asked for a payment then you shipped the item. Now you are essentially buying back the item, so why should he s...
Refund first, then you ship item back. He owes you return shipping money too.
When he bought the item, did you first ship the item then expect a payment? No, you asked for a payment then you shipped the item. Now you are essentially buying back the item, so why should he s...