All posts liked by PEDRONX2k
videos of noises will never reflect how it sounds in real life.
Ive been getting some odd pinging noises from the chain side of my engine recently, car is off the road now though and I will be t...
We're you low on oil, some people don't remember to check oil levels since vvl burn up a decent amount of oil. Glad you got the issue fixed. Congrats
I dig the Nismo IDX front end. Makes me think shark face. Ford is coming out with a 2.3L Turbo Mustang. It's a pretty good looking car too. Ford is on a good run lately. Focus ST, Fiesta ST, Turbo ...
Looks more like a B210, which is not one of my favorite Datsuns.:confused:
https://encrypted-tbn0.gstatic.com/images?q=tbn:ANd9GcRs7gtvbJwE2W2DredaXv0qRApgGSb1U8eU2e_yVKexq7wb3a_m
I'm going to reserve judgement until I see a road-going test mule, but I could live with this profile...
http://liveimages.motoring.com.au/motoring/general/editorial/ge5181846021183156342.jpg?he...
Please tell me you're not talking about a Trans cooler for a manual trans.
The rear motor mount is what kills the 5 speed trans, I don't care what anyone else says. Changed the mounts in my car...
Scored a second set of EDM headlights from my man up North and did another retrofit. The blacked out reflectors didn't do it for me. I like the blingy reflectors better...sho perty!
[url= URL=http...
I have noticed that my '92 NX2000 also has a horrible turning radius. My b14 can make a u-turn on my street but the NX doesn't even come close. It's worse than my girlfriends '00 maxima.
I'm located in Washington state so I'm pretty close to Canada I guess I could take a day trip up there if needed :) thanks
Jesus that modification dominates up top. Nice work!
i packed the shit out of my rack with almost a whole tube of red grease, then put grease fittings where the nuts used to be.
I once got on a highway without torquing all the lug nuts down and that was a fun time. Pulled over and was able to take lug nuts off by hand with tire on the ground lol...shit happens, give the gu...
That's not dramatic. Without that nut, the bearing will get fucked and if you grenade a wheel bearing your wheel could fly off. Hopefully the bearing is not trashed
...yeah,you should check stuff like that before taking your MOM for a ride too.Could have killed both of you.
Updating my interior b13/200sx se-r
In fact the TDC mark on the crank pulley didn't match. We used the long rod into cylinder 1 and rotated the engine manually and also by blowing compressed air into the opposed cylinders.
car won't start after cam install
yeah kinda looks like it's off, hope you rotated it first by hand before you just used the starter to start the car.
I would take the two hour ride back down there and get my money back. That's fucked up.
My car runs good at 70-80psi with no vac line connected. Running a big pump and injectors at that NA. ;)
http://i1201.photobucket.com/albums/bb356/B15NEOVVL/1fd29138-0ae4-43c0-86fb-f1363cbeef80_zps7c9d5dca.jpg
http://i1201.photobucket.com/albums/bb356/B15NEOVVL/3c3e9661-0f0d-4f59-be6d-e5ca8192a8d8_...
JC, it clears the radiator perfect. Barely clears my slim fans but it does clear them. Thanks again.
http://farm4.staticflickr.com/3710/10540123054_155dda5012.jpg
http://farm6.staticflickr....
thats the ideal lol...
even though i hope it wont happen again