rojeda1217's Likes Given

Lol, no one mentioned the obvious yet?

DOWELL PINS!

Should be 3 in the flywheel and 2 in the engine/trans I've seen several clutches fail from a missing Dowell pin..

Here's one from a week...

I haven't even seen it today... :(

There is so much snow outside, I didn't dare to walk out the the garage :(

1st loosen the 12mm or 11mm cant recall then use long skinny needle pliers to turn rod ,i also have mine almost all the way out only few threads holding it lol but with bolt nice and tightened, thi...

Not sure on p11, maximas rod appears to be able to turn..

I didn't have an issue getting my clevis back on the lever, it's nearly turned all the way out but good thing it's a push style clevis ...

B13 to RWD/AWD Conversion Questions

Worse, from what I've been told. Car would have to be certified by Nissan Mexico to meet Mexican "DOT" standards. i.e. It'd cost you the same as just bringing it here.

Now if you were to import ...

Yes, I got all the geometrical measurements from the fsm and made sure everything was precise before I welded. I will get some pics this evening and post them up.

http://www.harborfreight.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/i/m/image_20411.jpg

got this bad boy last weekend to fix some rust holes on the p10. Read a bit be...

Your best bet is a rad from an NX20t.

what a pain in the ass this conversion is...too many options and scattered info everywhere
Just when I thought I had the right pedal for my B13,I find contradicting info all over.

I hope someday s...

Keo is right, I pulled the clutch pedal from an 03 Maxima and it was exactly like you have pictured. 2 bolts holding it up top.

I skimmed through the thread but from researching and getting ready...

Dampner removed went to vatozone and grabbed female/female piece [URL="http://[url= URL=http://s592.photobucket.com/user/ztunedsr20/media/Mobile%20Uploads/20150525_150359_zpsm8fmk8xi.jpg.html][img...

WARNING this was done on a b14, Hope it helps anybody doing this upgrade not as a nightmare story as everyone tells I was able to do this on my trailer park driveway no shop no welder needed again ...

Ok I used 1999 p11 everything from lsd tranny, pedal, Mc slave reservoir, I made the 3rd top hole wider on the pedal to the stud inside the firewall and fit nice on my b14 I left the firewall botto...

the OP of the thread has the wrong maxima pedal which is why it dosent fit.

93-01 altima or 95-99 maxima pedals are best for both b13 and b14. for the b13, the upper hole needs to be widen out ...

Theres lots of threads that go over this procedure. I just did it in my b13. You can use the remote reservoir from a b15 cmc on the maxima cmc, I'm not sure what pedal is best suited for the b14 as...

rojeda1217 it worked great! I just had to move it to the alternate pivot point.

LOL at the punch babies comment...
anyway.To me it really sounds like a cable problem.I have had the same issues with an old cly=utch cable or a crappy aftermarket one.
Actually IO had a car that...

My experience is not directly from an FX500 kit. It is with a similar style kit on a completely different chassis (BMW). It was a 4-puck, ceramic disc (unsprung) well rated for the torque output of...

Mine was the water pump, seals expand when warm, contract when cold, mine only leaked when cold,
.
I just took the bolts out of the cross member motor mounts, removed the passenger mount and jack...

All the 30+ MPG guys must be shifting every gear below 2000RPM or something

I saw a tranny walk into a biker bar once. It was "removed" in about 10 seconds.

looking for a checklist type of thing I know there out there.

so swapping out the tps and iacv helped? you arnet getting the slight miss throughout the powerband

http://www.reactiongifs.com/wp-content/uploads/2014/01/Tom-Hanks-orly.gif