Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: I burn EPROM chips.

+ Reply To Thread
Posts: 1-10 of 64
2011-11-08 01:44:15
#1
I burn EPROM chips.
Like the title says, I burn chips.

I have extra chips laying around and if there is any interest I would be more then happy to help a few members out. I have most of calums base bins saved onto my computer as well as a few other safe bins. I can also change MAF's, Injectors, o2 feedback, rev limits, speed limits and minor timing adjustments. All fuel maps will be a base calum map. Even though the bins I am producing are what I consider safe, I can not be responsible for any issues the bin or installation may cause. Please keep in mind that calums bins were intended to get your car up and running and to a tuner who can tune the car to you specific needs. I am also going to recommend that your mechanical timing that is adjusted through the distributor should be set at 15* and all equipment in your vehicle should be working properly.

Im not trying to make much of a profit off of this, I figured it would help our community out a bit.

The prices will be:

$35 for a chip burn. (Buyer sends chips in to me and i ship them back out)

$30 shipped for a blank set of chips.

$60 shipped for 2 EPROM chips with a base bin. (I supply the chips)

If you have any problems with the chips I will be more then happy to try and help fix your problem and re-flash the chips if needed for no fee, however buyer must pay shipping both ways and the tune can not be for a different set up (maf's, injectors, cams, ect..) again shipping costs will be at the buyers cost.

Also

If you are interested in any other types of tuning feel free to ask. I offer Dyno, Street, Remote, E-Tunes and base maps for most platforms.

I also can perform any daughter board installation that you would like.
Last edited by D-Unit121 on 2016-06-02 at 12-44-47.
2011-11-10 15:20:46
#2
im going to pm you sir.
2011-11-11 05:12:17
#3
Are these for Calum Basic too?

What kind of chips can you get? My bud keeps ranting about the authentic vs cheap new version chipsets.

PM me about this please.
2011-11-11 07:36:18
#4
this link will shed light on what ben's talking about:

Fake 27SF512 Chips! « Moates Support

right from the moates site..
2011-11-11 15:43:08
#5
Originally Posted by D-Unit121
Like the title says, I burn chips.

I have extra chips laying around and if there is any interest I would be more then happy to help a few members out. I have most of calums base bins saved onto my computer as well as a few other safe bins. I can also change MAF's, Injectors, o2 sensor outputs and minor timing adjustments. All of the AFR's and timing will be safe.

Im not trying to make much of a profit off of this, I figured it would help our community out a bit.

The prices will be:

$10 for a chip burn. (Buyer sends chips in to me and i ship them back out)

$20 for a chip burn with lightly and safely modified bin. (Buyer sends chips in to me and i ship them back out)

$30 shipped for 2 EPROM chips with a base bin. (I supply the chips)

$50 shipped for 2 EPROM chips with a lightly and safely modified bin. (I supply the chips)


I think you need to change this statement.

There is no way for you to know how your "modified bin" will react to another setup. "Safe" in one location/setup can be dangerous in another.
2011-11-12 14:24:33
#6
Originally Posted by Benito
Are these for Calum Basic too?

What kind of chips can you get? My bud keeps ranting about the authentic vs cheap new version chipsets.

PM me about this please.


Originally Posted by lynchfourtwenty
this link will shed light on what ben's talking about:

Fake 27SF512 Chips! « Moates Support

right from the moates site..



Thanks for the link, and I understand the concern. I have real legit SST chips. Ill post up some pics later today if there is that much concern about them.
2011-11-12 14:30:23
#7
Originally Posted by SR20GTi-R
I think you need to change this statement.

There is no way for you to know how your "modified bin" will react to another setup. "Safe" in one location/setup can be dangerous in another.


Im not selling bin's that are fully tuned. It is a base bin with light timing modifications and very light fuel map tuning. Its more of a base map with a little love put into it. If you consider that dangerous, then a JWT programmed ECU must be a complete nightmare in your eyes. No disrespect to you SR20GTi-R and your knowledge but my bins are as safe as it can be.
2011-11-12 14:53:59
#8
Originally Posted by D-Unit121
Im not selling bin's that are fully tuned. It is a base bin with light timing modifications and very light fuel map tuning. Its more of a base map with a little love put into it. If you consider that dangerous, then a JWT programmed ECU must be a complete nightmare in your eyes. No disrespect to you SR20GTi-R and your knowledge but my bins are as safe as it can be.


Im just trying to help you out.

Trust me when I tell you, its better to have your ass covered. If you sell a set to someone who just tosses them in without verifying that all components of their setup are functioning properly, it will come back to you as your fault if it blows up.

My concern is not in the general fuel and timing maps, but in the overall fuel trims and TP load scales. Different cars respond different. Especially with different TPS and base timing settings.

Sorry for cluttering this thread. Mods please delete my posts.
2011-11-12 19:53:23
#9
can i send you a set of chips and tell me what someone burned on them?
2011-11-12 20:12:50
#10
Originally Posted by SR20GTi-R
Im just trying to help you out.

Trust me when I tell you, its better to have your ass covered. If you sell a set to someone who just tosses them in without verifying that all components of their setup are functioning properly, it will come back to you as your fault if it blows up.

My concern is not in the general fuel and timing maps, but in the overall fuel trims and TP load scales. Different cars respond different. Especially with different TPS and base timing settings.

Sorry for cluttering this thread. Mods please delete my posts.


you bring up a good point. Im basing all of the bins off of base bins for the setup. The overall fuel trim and load scales will be set up to work with all applications. However if someone has a bad component in their setup then there could be an issue with running any bin.

Originally Posted by 2dr_sentra
can i send you a set of chips and tell me what someone burned on them?


Sure, I will send you a PM to discuss shipping charges.
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top