Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: nismotronic ecu

+ Reply To Thread
Posts: 11-20 of 32
2016-02-02 04:11:49
#11
Originally Posted by naturaLeza
even tho i dont have my ign light on the ecu should ground out my eccs relay right


Actually, it probably won't if it isn't getting power and booting up correctly.

What pins do you have 12v to?
2016-02-02 20:07:04
#12
pin #56 (power supply)
pin #61 (power supply)
pin #70 (power supply back up)
pin #113 (current return)
2016-02-03 00:31:55
#13
Originally Posted by naturaLeza
pin #56 (power supply)
pin #61 (power supply)
pin #70 (power supply back up)
pin #113 (current return)


You are missing pins 38|39 and the two right below it.
2016-02-03 00:54:50
#14
pin #38 is ignition switch (this is only connected to my distributor @ #6 wire)
pin #39 is eccs ground ( this is 1 of 7 eccs grounds grounded to the chassis)
the 2 other pins which you are referring to are they #40 and #41 or @ the connector?

i am using 95-97 b series harness pin out with boomslang jumper harness
Last edited by naturaLeza on 2016-02-06 at 04-57-26.
2016-02-05 21:40:12
#15
Originally Posted by naturaLeza
pin #38 is ignition switch (this is only connected to my distributor @ #6 wire)
pin #39 is eccs ground ( this is 1 of 7 eccs grounds grounded to the chassis)
the 2 other pins which you are referring to are they #40 and #41 or @ the connector?

i am using 95-97 b series harness pin out with your jumper harness


You need pins 46, 47 and 38 on the OBD1 B13 connector side to have power. (including the ignition ON signal at pin 38).
2016-02-06 17:44:35
#16
Ok, since I'm not connecting power correctly, I'll keep searching the plugs for that ign signal, sorry.
Last edited by naturaLeza on 2016-02-07 at 03-06-23.
2016-03-02 00:56:29
#17
ok, so now my ign on is illuminated and and the eccs relay (self-shut off) is grounding out on its own (pin #38 ignition switch is a shared wire). Turns out that the same wire that powers the injectors(blk/red) is also used for the ignition switch (12v@on/start). Figured out that pin#20 start signal is a b/y wire (12v@start). Next is the ignition signal and ignition check wires. Thanks John


ok, ign signal/ign check are not shared wires and only connect to the distributor. Next I'm going to try and start the car.
Last edited by naturaLeza on 2016-03-03 at 01-11-00.
2016-03-03 23:25:47
#18
ok, tried to start the car. I have no spark and injectors are not firing. My cranking light on the nemu comes on briefly while trying to start. What am I missing? Does the ecu need to see a sensor to start?
2016-03-04 01:32:55
#19
If no signal from CAS you won't get spark and injectors won't fire

Seems like you've made shit more difficult then it needed to be.. i would have left the de distributor and used a step down harness
2016-03-07 16:50:54
#20
Ok.. so the ve doesn't have that in the distributor.
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top