Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: The Ultimate 6 Speed Swap Thread...Parts/Instructions/Results!!

+ Reply To Thread
Posts: 21-30 of 485
2012-12-11 04:27:59
#21
Originally Posted by LikeTheMovies
What if you have a digital cluster? Any way to get that to work correctly with the swap?


whats the problem?
2012-12-11 04:47:56
#22
Originally Posted by unijabnx2000
Originally Posted by LikeTheMovies
What if you have a digital cluster? Any way to get that to work correctly with the swap?


whats the problem?


I havent done the swap just curious will the spec trans take a sr speed sensor?
2012-12-11 05:17:28
#23
Yes, it will take the 6 speeds sensor. All the electronic speedometer sensors will read each other. Only difference is the gear to get the proper speed. You can swap your current electronic speedometer sensor into the 6 speed again you will have to cut the tab just like the cable version.
2012-12-11 13:03:04
#24
Awesome thread. Thread of the year
2012-12-11 23:27:28
#25
What is everyone doing for clutch and flywheel bolts, are the stock ones being used?
2012-12-11 23:35:32
#26
Originally Posted by nismosigma
What is everyone doing for clutch and flywheel bolts, are the stock ones being used?


I believe you use your stock flywheel bolts, I know for a fact the gspec flywheel comes with new pressure plate bolts.
2012-12-11 23:42:44
#27
I have a question about the crank sensor in the trans (B14), I was just thinking about it right now and have not checked the new bell housing or the flywheel. Does the bellhousing have the provision for the crank sensor and does the gspec flywheel work for the crank sensor?
2012-12-11 23:58:54
#28
Originally Posted by nismosigma
What is everyone doing for clutch and flywheel bolts, are the stock ones being used?


Well it depends on which flywheel you buy. I got an S15 flywheel, and it came with crank bolts, which are longer than stock I believe. I bought pressure plate bolts from lowes. Cap head grade 12.9 M8-1.25x16mm.
2012-12-12 01:57:27
#29
Originally Posted by boriquas13
I have a question about the crank sensor in the trans (B14), I was just thinking about it right now and have not checked the new bell housing or the flywheel. Does the bellhousing have the provision for the crank sensor and does the gspec flywheel work for the crank sensor?


Thats a good question. I believe it does have the provision but you have to drill it out and tap the bolt hole. I believe the flywheels have the proper amount of teeth as well to not trigger a cell. Look through coheeds thread as Im almost certain he did this mod. It should be in there.
2012-12-12 03:41:54
#30
Originally Posted by ashtonsser
Originally Posted by boriquas13
I have a question about the crank sensor in the trans (B14), I was just thinking about it right now and have not checked the new bell housing or the flywheel. Does the bellhousing have the provision for the crank sensor and does the gspec flywheel work for the crank sensor?


Thats a good question. I believe it does have the provision but you have to drill it out and tap the bolt hole. I believe the flywheels have the proper amount of teeth as well to not trigger a cell. Look through coheeds thread as Im almost certain he did this mod. It should be in there.


There are provisions for the sensor, and it does work. But it does tend to be a little finicky. Make sure everything lines up right and you should be good.
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top