My high CR build - Page 4 - SR20 Community Forum

STRATTON · 12-17-2007, 08:22 PM

very nice build man, i cant wait to see what this motor makes as i have had thoughts of something very similiar.

my i recommend you clean, scuff, clean, tape off, prime and pain the bay. itll put a big smile on your face every time you pop the hood plus the motors is out why not.

stratton.

GT2871RBLUBIRD · 12-18-2007, 12:38 AM

nice build

Eric93whitesr20 · 12-18-2007, 05:58 PM

get it done rob you been sitting on that thing for awhile

B15sentraDE · 12-18-2007, 06:29 PM

swap looks good man, very simlar to what im finishing up. exept i went with 11.0 cp, and c3 cams. definatly let us all know when its running, hopefully mine is up and running this weekend.

Robchaos · 12-18-2007, 07:17 PM

LOL awesome. I will be attempting to start mine saturday. Whether it actually starts or not will be another story

.
Crossing my fingers. I will most definately be taking video and sound clips.

se-riousjdm · 12-19-2007, 11:59 AM

cant wait for some results been watching this thread..this thread is actually going to decide which route i choose so i'm crossing my fingers for you also lol..good luck and good job man

Robchaos · 12-19-2007, 10:04 PM

Hit a minor snag with the PS manual rack install today. I neglected to research, and I need to purchase a knuckle u joint, and tie rod ends for a manual rack, but otherwise the engine is still scheduled for start up saturday!

Kundara88 · 12-19-2007, 11:19 PM

I'm going to be watching this thread daily for updates, i wont post much, but i'll be watching....haha. I like your N/A set up

Robchaos · 12-19-2007, 11:38 PM

I updated the first post of this thread with old pictures from when I first started. (originally posted on sr20forum.com)

GTi kurt · 12-20-2007, 01:49 PM

What's your ball park figure? Must be circa 175whp?

Robchaos · 12-20-2007, 06:41 PM

that seemed to be around what people have estimated this setup will put out.
Nissan is overniting the steering knuckle joint I need, so everything is still looking good for saturday!

SGTSR20 · 12-21-2007, 05:30 AM

whats your rev limit on this????

hook us up with some video clip when its done.

Robchaos · 12-21-2007, 06:48 AM

7950 rpm using a jwt ecu. If I wanted the red line higher then that, they said that all they can do is remove it completely then I'd have to get an MSD system or something to set the rev limit.

Robchaos · 12-22-2007, 03:08 PM

It started!!!!

That thing sounds badass turning over. Movie and sound clips to come soon!

Hit a couple snags though,
The clutch cable is way too long, (I have a ga16 cable to put in, and am getting the reducer mod),
and the thermostat wouldn't open (a brand new stant thermo at that). So I am going back up their monday with a thermostat and the clutch cable to finish it up.

I am so excited!

Keo · 12-22-2007, 04:34 PM

I have a brand new Nissan oem thermostat if you need it!

12-19-2007, 11:38 PM	#54 (permalink)
Robchaos Robusto Join Date: Dec 2007 Location: Maryland iTrader: (9)	I updated the first post of this thread with old pictures from when I first started. (originally posted on sr20forum.com) __________________ “Undermine their pompous authority, reject their moral standards, make anarchy and disorder your trademarks. Cause as much chaos and disruption as possible but don’t let them take you ALIVE.” Visit my vendor section here.

12-20-2007, 06:41 PM	#56 (permalink)
Robchaos Robusto Join Date: Dec 2007 Location: Maryland iTrader: (9)	that seemed to be around what people have estimated this setup will put out. Nissan is overniting the steering knuckle joint I need, so everything is still looking good for saturday! __________________ “Undermine their pompous authority, reject their moral standards, make anarchy and disorder your trademarks. Cause as much chaos and disruption as possible but don’t let them take you ALIVE.” Visit my vendor section here.

12-21-2007, 05:30 AM	#57 (permalink)
SGTSR20 greasemon-k Join Date: Dec 2007 Location: NC iTrader: (3)	whats your rev limit on this???? hook us up with some video clip when its done. __________________ 95' P10 Dark Green, SR20VE,N1' cams, 16VE tranny, NOSsss 96' B14 White T28@11psi, S3's cams 98' B14 Blue Mettalic. sold!

12-21-2007, 06:48 AM	#58 (permalink)
Robchaos Robusto Join Date: Dec 2007 Location: Maryland iTrader: (9)	7950 rpm using a jwt ecu. If I wanted the red line higher then that, they said that all they can do is remove it completely then I'd have to get an MSD system or something to set the rev limit. __________________ “Undermine their pompous authority, reject their moral standards, make anarchy and disorder your trademarks. Cause as much chaos and disruption as possible but don’t let them take you ALIVE.” Visit my vendor section here.

12-22-2007, 03:08 PM	#59 (permalink)
Robchaos Robusto Join Date: Dec 2007 Location: Maryland iTrader: (9)	It started!!!! That thing sounds badass turning over. Movie and sound clips to come soon! Hit a couple snags though, The clutch cable is way too long, (I have a ga16 cable to put in, and am getting the reducer mod), and the thermostat wouldn't open (a brand new stant thermo at that). So I am going back up their monday with a thermostat and the clutch cable to finish it up. I am so excited! __________________ “Undermine their pompous authority, reject their moral standards, make anarchy and disorder your trademarks. Cause as much chaos and disruption as possible but don’t let them take you ALIVE.” Visit my vendor section here.

12-17-2007, 08:22 PM	#46 (permalink)
STRATTON BLUE RAY PWNES ME Join Date: Dec 2007 iTrader: (1)	very nice build man, i cant wait to see what this motor makes as i have had thoughts of something very similiar. my i recommend you clean, scuff, clean, tape off, prime and pain the bay. itll put a big smile on your face every time you pop the hood plus the motors is out why not. stratton.

12-18-2007, 12:38 AM	#47 (permalink)
GT2871RBLUBIRD Turbo Nut. Join Date: Dec 2007 Location: CinCinnati iTrader: (1)	nice build

12-18-2007, 05:58 PM	#48 (permalink)
Eric93whitesr20 formally Eric96redsr20 Join Date: Dec 2007 Location: about to be CT iTrader: (0)	get it done rob you been sitting on that thing for awhile

12-18-2007, 06:29 PM	#49 (permalink)
B15sentraDE Member Join Date: Dec 2007 iTrader: (0)	swap looks good man, very simlar to what im finishing up. exept i went with 11.0 cp, and c3 cams. definatly let us all know when its running, hopefully mine is up and running this weekend.

12-18-2007, 07:17 PM	#50 (permalink)
Robchaos Robusto Join Date: Dec 2007 Location: Maryland iTrader: (9)	LOL awesome. I will be attempting to start mine saturday. Whether it actually starts or not will be another story . Crossing my fingers. I will most definately be taking video and sound clips.

12-19-2007, 11:59 AM	#51 (permalink)
se-riousjdm Learning Join Date: Dec 2007 Location: Jamica Queens iTrader: (2)	cant wait for some results been watching this thread..this thread is actually going to decide which route i choose so i'm crossing my fingers for you also lol..good luck and good job man

12-19-2007, 10:04 PM	#52 (permalink)
Robchaos Robusto Join Date: Dec 2007 Location: Maryland iTrader: (9)	Hit a minor snag with the PS manual rack install today. I neglected to research, and I need to purchase a knuckle u joint, and tie rod ends for a manual rack, but otherwise the engine is still scheduled for start up saturday!

12-19-2007, 11:19 PM	#53 (permalink)
Kundara88 Boost > NA Join Date: Dec 2007 Location: Seattle, WA iTrader: (2)	I'm going to be watching this thread daily for updates, i wont post much, but i'll be watching....haha. I like your N/A set up

12-20-2007, 01:49 PM	#55 (permalink)
GTi kurt The Stig Join Date: Dec 2007 Location: Chester, England iTrader: (0)	What's your ball park figure? Must be circa 175whp?

12-22-2007, 04:34 PM	#60 (permalink)
Keo I dunno * Forum Supporter * Join Date: Dec 2007 Location: Maryland iTrader: (27)	I have a brand new Nissan oem thermostat if you need it!

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode