Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: DE head package - on a budget - infotainement

+ Reply To Thread
Posts: 11-20 of 111
2014-10-06 18:04:22
#11
I really have no clue so here's a shot in the dark: template for cutting valve seats??
2014-10-06 20:56:01
#12
Originally Posted by P10
I really have no clue so here's a shot in the dark: template for cutting valve seats??


First... thanks for getting involved... it does make these more fun...

it isn't a template for cutting valve seats... It does have to do with the valves

when finished, it will be a tool, absolutely required for learning if I'm just hogging this out, or actually improving the air flow.

Let me drop a few more hints....



halve 29....









Knowing it will be a tool.... Did that make it easier... or harder???


More to come......
Last edited by oldeskewltoy on 2014-10-06 at 20-58-28.
2014-10-06 21:42:48
#13
OK. Looks like it's used to hold the valves open? So you can perform the flow test right?
2014-10-06 21:43:58
#14
exactly.
2014-10-06 21:45:20
#15
Sweet that's awesome
2014-10-07 02:12:03
#16
bingo... it is the tool I'll be using to set the valve openings....

Here is a sample of it in use... the use is to show the viewers that I can set this tool at any height... note the tool on the bottom of the photo... and note the valves @ the top of the photo





Now being able to set the valves is important... just as important is knowing exactly how much... so I plan for the plate to accept a dial guage to read the amount of lift




and the finished tool......



The dial gauge will "read" from the edge of the spring retainer



more to come.......
2014-10-07 02:14:51
#17
Nice!
2014-10-07 02:35:26
#18
Originally Posted by P10
Nice!

thanks....

the view as mounted to the head...




Now that the valve setting tool is finished, its time to re-configure my flowbench to measure the SR20 head. Earlier this past summer I had a new bore adapter "machined" to 86mm



so that I can then place an SR20 headgasket on the bench to determine where the alignment dowels will be drilled into the flowbench table to properly align the head over the 86mm bore adapter.



Here is the "view" the flowbench will see...






More to come.......
2014-10-07 02:38:39
#19
Going on my letter to Santa... Bore adapter and flowbench... Got it!
2014-10-07 19:31:23
#20
Now... where was I before I got us side tracked on tool development....



Oh yes...

Originally Posted by oldeskewltoy

1 - as I mentioned, the casting is a bit rough leaving many areas containing sharp edges. From my experience, often times poor casting areas lead to sludge build up because the oil and debris sits in these areas "cooking" into place as the miles go by. Making these areas less prone to holding the oil and debris, helps keep the engine cleaner, and easier to shed oil back into the oil pan. A second, and purely selfish purpose is with me constantly changing its position on my porting bench, the roughness really hurts my hands.....

2 - below is a view of the Chambers #3 and #4 , I've blacked out the valve openings to avoid distraction....

As you can note, other then doing a tiny bit of blending around the seats, putting a ~.020" radius on both "squish" pads, and polishing the chambers I've had to do very little.



A small addition , as for the roughness/sharp edges, you can see preliminary deburring in the photo above that shows the tool mounted to the head. You can see where I ran the carbide cutter along some of the edges.

As far as chamber shapes - and, in fact, all the work I'm performing is "on a budget". So.... I will not be welding and re-shaping combustion chambers, that is prohibitively expensive (Thousands$$$) because for the most part less than .5% of you would ever consider paying for that kind of modification. Typically I delivery a finished product for well under $1000.


So we have discussed the casting and its requirements, and the combustion chambers. Now we come on the difficult part trying to increase the cylinders breathing capability. Note I said increase, because I'm NOT looking to discard(swap) low speed performance, in favor of high speed performance. The best goal is to provide a W I D E powerband.



Borrowing Martins dyno, I've made a few alterations



The dotted red lines I see as air flow problems(or how they will respond once corrected), the green lines is the desire for MartinS engine once we put this heads development into practice, along with his camshaft choice and appropriate compression bump.




A few different views of the intake port passages....






Now compare those views with a few others.....



Same similarities... while there are other differences....

Two of the views above seems to show the SR20 intake ports to have a similar shape to a Formula One design but hold on... the F1 design doesn't have an HLA to avoid :angry:, the top view showing the port layout is our issue here. The port opening is marginally 50mm (do to costs, the port opening varies at the seam from 49 to 50),


the intake valves are less than 9mm apart from each other,


and the HLA makes the port splitter somewhere close to 23-24mm at its widest point.... and so you get a bow legged intake port.....


More can be done here ... mostly because this is a production automobile head, and as such typically there is enough casting material available to better shape, not only the intake port... but often the entire head.




More to come.......
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top